Counter Drawing Or Reverse Drawing Presses
Approx. Rs 4.5 Lakh / Piece
- Minimum Order Quantity: 1 Piece
- Control Type: CNC, Non-CNC
- Max Force or Load: 0-30 ton, 120-150 ton, 90-120 ton, 30-60 ton, >150 ton, 60-90 ton
- Automatic Grade: Manual, Automatic, Semi-Automatic
- Brand: Santec
- Phase: 3 Phase
- Voltage: 415 Volt
- Color: As per customer requirement
- Country of Origin: Made in India
This innovative concept is an energy saving & cost effective, high production & highly suitable for long draw depth components i.e. Geyser body etc. As shown below, the top die is attached to the slide. The lower die is mounted on the press bed with the blank holder. The punch is located in an opening in the center of the press bed on the draw cushion cylinder.
In this operation, once again, a single Action press with a draw cushion is used. Pushing deformation, the blank holding force is transferred via the slide from above & the draw punch force acts from below through the active draw cushion. The punch forms the post by means of its upward movement while the blank holder rests on the die.
The active Counter drawing combines the advantages of static blank holding & the low power usage of double action dies with the advantage of a single Action die. Admittedly, it is necessary to have a special modification of the dies for performing this operation, since the forces operate in the opposite direction to those of a normal single action deep drawing press with draw cushion. Thus, these dies can not be installed in a normal single Action press.
Characteristic | Mechanical Presses | Hydraulic Presses |
Force | Variable (depends on slide position) | Relatively constant (does not depend upon slide position) |
Stroke length | Limited | Capable of long stroke 100 or more |
Slide Speed | Higher Speed Capability | Slower pressing speeds with rapid advance & retraction variable speeds uniform throughout stroke |
Control | Full Stroke generally required before reversal | Full Stroke generally required before reversal |
Applications | Blanking, Shearing, Piercing, Drawing only upto 4 inches | Deep Drawing, Straightening etc.
|
Price will be different according to Customer Requirement
Additional Information:- Delivery Time: 2 to 3 Months
- Packaging Details: Polythene packed
Double Action Deep Drawing Presses with Blank Holders
Approx. Rs 8.5 Lakh / Ton
- Minimum Order Quantity: 1 Ton
- Automatic Grade: Manual, Automatic, Semi-Automatic
- Max Force or Load: 90-120 ton, 60-90 ton, 120-150 ton, 30-60 ton, 0-30 ton, >150 ton
- Control Type: CNC, Non-CNC, Hydraulic
- Brand: Santec
- Frame Design: C Frame Type, H Frame Type, 4- Pillars Type Design, Ring Type , Closed Frame
- Surface treatment: Painted
In double – action Drawing operations the press has two slides acting from top:- the drawing slide with the draw punch & the blank holder slide with the blank holders as shown below
The Blank holding slide transfers the blank holding force via. The blank holder onto the blank & the draw die. The die & the ejector are located in the lower die on the press bed. During forming, the blank holder brings the sheet metal into contact against the die, the punch descends from above into the die & shapes the part while the sheet metal can flow without any wrinkling out of the blank holding area. In this Case, the drawing process is carried out with a fixed blank holder & moving punch. In double action drawing operations, the drawing slide can only apply a pressing force.
These double Action drawing presses are also available in both pillars type & frame design. Custom built presses with features as per requirement of customer / applications can be designed & manufactured.
Note: Price will be change as per Customer Requirement
Additional Information:- Port of Dispatch: All Over World
- Delivery Time: 3 Months
- Packaging Details: Polythene and Wooden Packing
Double Action Deep Drawing Presses with Blank Holders
Approx. Rs 7.5 Lakh / Ton
- Minimum Order Quantity: 1 Ton
- Max Force or Load: 120-150 ton, 0-30 ton, 30-60 ton, 90-120 ton, >150 ton, 60-90 ton
- Automatic Grade: Manual, Automatic, Semi-Automatic
- Brand: Santec
- Control Type: CNC, Non-CNC
- Material: Cast iron
- Surface treatment: Painted
In double – action Drawing operations the press has two slides acting from top:- the drawing slide with the draw punch the blank holder slide with the blank holders as shown below
The Blank holding slide transfers the blank holding force via. The blank holder onto the blank the draw die. The die the ejector are located in the lower die on the press bed. During forming, the blank holder brings the sheet metal into contact against the die, the punch descends from above into the die shapes the part while the sheet metal can flow without any wrinkling out of the blank holding area. In this Case, the drawing process is carried out with a fixed blank holder moving punch. In double action drawing operations, the drawing slide can only apply a pressing force.
These double Action drawing presses are also available in both pillars type frame design. Custom built presses with features as per requirement of customer / applications can be designed manufactured.
Hydraulic Double Action Deep Draw Press
Approx. Rs 7.5 Lakh / Unit
- Minimum Order Quantity: 1 Unit
- Automatic Type: Semi-Automatic, Automatic
- Capacity: 10-20 Ton
- Brand: Santec
- Type of Press: C-Frame Press, Assembly Press, H-Frame Press
- Control Type: CNC, Non-CNC
- Material: Iron
- Condition: New
- Color: Customised
Technical Specifications |
Type | Vertical Four Columns Type Structure, Frame is fabricated out of ultrasonically tested Steel Plates duly welded with suitable reinforcements to give strength & load during operation. |
Capacity Of The Main Ram | 120 MT (1no.) |
No. Of Cylinders / Ram | 1 no. main Cylinder + 2 nos. side Jacking Cylinders for blank holder’s fast down & fast up movement + 6 nos. blank holder cylinders fixed at equal distance for uniform distribution of blank holder force or better clamping of sheet + 1 no. ejector cylinder . |
Bed Size or Bolster Plate | 1100 mm (LR) x 900 mm (FB) |
Bore (piston) Dia. of Main Cyl. | 11" |
Stroke Length Of Main Cylinder | 500 mm (Adjustable) |
Open Daylight | 700 mm |
Blank Holder Cylinder's Capacity | 80 Tons |
Stroke Length Of Blank Holder Cylinders: | 300 mm |
Advanced or Approach Speed | 90 - 100 mm/sec. (Approx.) |
Drawing Speed | 8 - 10 mm/sec. (Approx.) |
Return Speed | 120 - 150 mm/sec. (Approx.) |
Working Pressure | 200 to 210 kg/cm2 |
Electric Motor | 15 H.P.,3phase,1440 R.P.M., ABB Make |
Pump | Double Pumps for high & low speeds |
Operation | PUSH BUTTON OPTD. WITH ELECTRICAL CONTROL PANEL. Both auto /manual mode of operation PLC - Operated control panel |
PLC | Omron / Siemens make with coloured touch screen for user friendly operation. |
Weight Of The Press | 6 - 7 Tons( Approx.) |
T-Slots Size | T-20 |
Double Action Deep Drawing Presses with Blank Holders
Approx. Rs 5.5 Lakh / Ton
- Automatic Grade: Automatic
- Max Force or Load: >150 ton
- Brand: Santec
- Surface treatment: Painted
- Material: Cast iron
In double – action Drawing operations the press has two slides acting from top:- the drawing slide with the draw punch the blank holder slide with the blank holders as shown below
The Blank holding slide transfers the blank-holding force via. The blank holder onto the blank the draw die. The die the ejector is located in the lower die on the press bed. During forming, the blank holder brings the sheet metal into contact with the die, the punch descends from above into the die shapes the part while the sheet metal can flow without any wrinkling out of the blank-holding area. In this Case, the drawing process is carried out with a fixed blank holder moving punch. In double action drawing operations, the drawing slide can only apply a pressing force.
These double Action drawing presses are also available in both pillars type frame design. Custom built presses with features as per requirement of customer/applications can be designed manufactured.
Single Action Drawing Presses
Approx. Rs 6.5 Lakh / Ton
- Automatic Grade: Automatic
- Max Force or Load: >150 ton
- Brand: Santec
- Surface treatment: Painted
- Material: Cast iron
'Santec' Hydraulic Deep Drawing Presses are preferred across the world because of many unmatched features. These heavy-duty Presses can perform 24 hours, fitted with PLC, touch screen, LVD, Pressure transmitter, Photo Safety guard of slide locking cylinders etc. as per European standards safety norms. The production rate of these presses is high consumed very less electricity in comparison of other.
Single Action drawing Press with bottom cushioning arrangement are available in both Pillars Frame design. Custom built presses with features as per requirement of customer/applications can be designed manufactured.
Upstroking Type Double Station Type Presses
Approx. Rs 5.5 Lakh / Ton
- Minimum Order Quantity: 1 Ton
- Condition: New
- Brand: Santec
- Material: Cast iron
- Surface treatment: Painted
- Automation grade: Automatic
'SANTEC' manufacture these Presses with an uncompromising Quality attitude & providing outstanding services world wide. SANTEC Engineer's are Competent enough to accommodate customer's suggestions & design the presses meeting all requirements as per International standards. In these presses, the Ram / slide / moving platen moves in upward direction (from Bottom Home Position to upward position). We have standard models & make these presses as per customer's specifications & requirement too.
Single Action Drawing Presses with Bottom Cushioning Arrange
Approx. Rs 6.5 Lakh / Unit
- Minimum Order Quantity: 1 Unit
- Automatic Grade: Manual, Semi-Automatic, Automatic
- Control Type: Non-CNC, CNC, Hydraulic
- Max Force or Load: >150 ton, 60-90 ton, 30-60 ton, 0-30 ton, 90-120 ton, 120-150 ton
- Brand: Santec
Santec' Hydraulic Deep Drawing Presses are preferred across the world because of many unmatched features. These heavy duty Presses can perform 24 hours, fitted with PLC, touch screen, LVD , Pressure transmitter, Photo Safety guard of slide locking cylinders etc. as per European standards & safety norms. The production rate of these presses is high & consume very less electricity in comparison of other.
Single Action drawing Press with bottom cushioning arrangement are available in both Pillars & Frame design. Custom built presses with features as per requirement of customer / applications can be designed & manufactured.
Santec's Action Drawing Presses with Bottom Cushioning Arrangements are specially designed for deep - drawing operations. These presses are used to handle tough processing, which cannot be done mechanically. They are widely across diverse industries for the following applications :
- Automobile deep drawn parts
- Housing / Containers of Compressor, filters etc.
- Geyser's Tank
- Sink / Tanks
- Household items
- Pans
- Bomb shell
- Aeroplane parts
Note: Price will be change as per Customer Requirement
Additional Information:- Port of Dispatch: All Over Workd
- Delivery Time: 3 Months
- Packaging Details: Polythene and Wooden Packing
Deep Drawing Presses
Approx. Rs 6.5 Lakh / Unit
- Minimum Order Quantity: 1 Unit
- Automatic Grade: Manual, Semi-Automatic, Automatic
- Max Force or Load: 0-30 ton, 60-90 ton, >150 ton, 120-150 ton, 30-60 ton, 90-120 ton
- Control Type: CNC, Hydraulic, Non-CNC
- Brand: Santec
Features- Ultrasonically tested quality plates are used of heavy thickness to make the frame more regid & capable enough to the load during frequent & fast operations
- Technical Specifications
Price will be change as per Customer Requirement
Additional Information:- Port of Dispatch: All Over World
- Delivery Time: 3 Months
- Packaging Details: Polythene and Wooden Packing
Single Action Drawing Presses with Bottom Cushioning Arrange
Approx. Rs 5.5 Lakh / Unit
- Minimum Order Quantity: 1 Unit
- Max Force or Load: 90-120 ton, >150 ton, 120-150 ton, 0-30 ton, 60-90 ton, 30-60 ton
- Control Type: Non-CNC, CNC
- Brand: Santec
- Automatic Grade: Automatic
'Santec' Hydraulic Deep Drawing Presses are preferred across the world because of many unmatched features. These heavy duty Presses can perform 24 hours, fitted with PLC, touch screen, LVD , Pressure transmitter, Photo Safety guard of slide locking cylinders etc. as per European standards safety norms. The production rate of these presses is high consume very less electricity in comparison of other.
Single Action drawing Press with bottom cushioning arrangement are available in both Pillars Frame design. Custom built presses with features as per requirement of customer / applications can be designed manufactured.